James M. Kelly

[1] “General Equations for Writing Rates of Streak Cameras,” Proceedings, 6th International Congress on High
Speed Photography, The Hague, Netherlands, (1962).
[2] “Phenomena of Penetration in Light Weight Personnel Armor Materials,” (with J. Corcoran), Report to the U.S.
Army Quartermasters Research & Engineering Command, Contract No. DA-19-129-QM-1574 (1962).
[3] “Further Studies in the Penetration of Light Weight Personnel Materials,” (with J. Corcoran), Report to the U.S.
Army Quartermasters Research & Engineering Command, Contract No. DA-19-129-QM-1574 (1962).
[4] “Precision of Narrow Pass Band Optical Pyrometry,” Interim Report, National Bureau of Standards, Order No.
S-103932-62 (1962).
[5] “A Phenomenological Superposition Model for Non-linear Visco-elasticity,” Technical Memorandum 64-
4253-32, Bell Telephone Laboratories (1964).
[6] “The Unloading Wave Problem in Viscoplastic Wave Propagation,” Technical Memorandum 64-4216-13, Bell
Telephone Laboratories (1964).
[7] “Stress Strain Relations for Strain Rate Sensitive Elastic Plastic Materials,” Technical Report No. 152, Division
of Engineering Mechanics, Stanford University (1965).
[8] “Precursor Attenuation in Elastic-Viscoplastic Materials,” Technical Report 157, Ballistics Research
Laboratories, Aberdeen Proving Ground, Contract No. CA-04-200-AMC-659(R) (1965).
[9] “The Impact of a Mass on a Beam,” International J. Solids and Structures, 3:191-196 (1967).
[10] “Motion of a Circular Visco-Plastic Plate Subject to Projectile Impact,” (with T. Wierzbicki, Institute for Basic
Technical Research, Polish Academy of Science, Warsaw), Zeit fur Angewandt Mathematik und Physik, Vol.
18, (1967).
[11] “Precursor Attenuation in Elastic, Visco-Plastic Materials,” (with P.P. Gillis), Proceedings, 1st Canadian
Congress of Applied Mechanics, Universite Laval, Quebec, I:1-150 (1967).
[12] “Generalizations of Some Elastic-Viscoplastic Stress-Strain Relations,” Transactions, Society of Rheology,
II:55-76 (1967).
[13] “Strain Rate Sensitivity and Yield Point Behavior in Mild Steel,” International J. Solids and Structures, 3:521-
532 (1967).
[14] “Dislocation Dynamics and Precursor Attenuation,” J. Applied Physics, 38:4044-4046 (1967).
[15] “Response of Clamped Circular Plates to Square Wave Stress Pulses,” (with T.R. Wilshaw), Experimental
Mechanics, 8(10):450-459 (1968).
[16] “Finite Deflection of a Circular Visco-Plastic Plate Subject to Projectile Impact,” (with T. Wierzbicki),
International J. Solids and Structures, 4:1081-1092 (1968).
[17] “An Experimental and Theoretical Study of Projectile Impact on Clamped Circular Plates,” (with T.R.
Wilshaw), The Royal Society, London, Vol. 306, Series A, p. 435-447 (1968).
[18] “On the Determination of Stress, Strain, Strain Rate Relations on Dynamic Beam Tests,” (with P.P. Gillis), J.
Applied Mechanics, 36:632-634 (1969).
[19] “Basic Mechanics Study for Computer Evaluation of Automobile Barrier Systems,” Report No. 69-10, Division
of Structural Engineering and Structural Mechanics, Department of Civil Engineering, University of
California, Berkeley, Calif. (1969).
[20] “Computing the Main Features of One-Dimensional Plastic Strain Waves,” (with P.P. Gillis), Proceedings, 2nd
Canadian Congress of Applied Mechanics, 1:143 (1969).
[21] “Oblique Impact on Rigid-Plastic Beam Support Barrier Systems,” (with W.S. Tseng), International J.
Nonlinear Mechanics, 5:183-196 (1970).
2
[22] “Shock Thickness in Visco-Plastic Solids,” (with P.P. Gillis), J. Applied Mechanics, 37:163-170 (1970).
[23] “Nonlinear Constitutive Equations for Plane Shock Propagation in Visco-Plastic Solids,” Arch. Mech. Stos.,
Polish Academy of Sciences, 22:93-110 (1970).
[24] “Finite Deformation Analysis of Shocks in Visco-Plastic Solids,” (with P.P. Gillis), Proceedings, United States
National Congress of Applied Mechanics, Harvard University (1970).
[25] “Thermal Effects on Shocks in Visco-Plastic Solids,” J. Mechanics and Physics of Solids, 18:397-412 (1970).
[26] “On Determining Material Properties from Plate Impact Tests,” Case 27540-3, Bell Telephone Laboratories
(1970).
[27] “Shock Induced Phase Transitions and Explosive Forming of Metals,” Bell Telephone Laboratories (1970).
[28] “Methods for Dynamic Material Testing,” Bell Telephone Laboratories (1970).
[29] “A Note on Yield Point Phenomenon in Wave Propagation,” International J. Solids and Structures, 7:1211-
1217 (1971).
[30] “Projectile Impact on an Infinite Viscoplastic Plate,” International J. Solids and Structures, 7:1143-1152
(1971).
[31] “Ideal Viscoplasticity,” Acta Metallurgica, 20:947-951 (1972).
[32] “Mechanisms of Energy Absorption in Special Devices for Use in Earthquake Resistant Structures,” (with R.I.
Skinner and A.J. Heine), Bulletin of the New Zealand National Society for Earthquake Engineering, 5(3):63-
88 (1972).
[33] “A Note on the Influence of a Limiting Dislocation Velocity on the Yield Point Phenomenon,” (with P.P.
Gillis), Zbornik Radova, XI Jugoslovenskog Kongrese racionalne i pnimenjene mehanike, Basko Polje (1972).
[34] “An Ideally Viscoplastic Analysis of the Yield Point Phenomenon,” (with P.P. Gillis), Acta Metallurgica,
21:343 (1973).
[35] “The Role of Dislocation Drag in Shock Waves,” Proceedings, AIME Conference on Materials at High Rates
of Strain, Albuquerque, New Mexico (1973).
[36] “Ideal Viscoplasticity: A Model for the Seventies,” Proceedings, Canadian Congress of Applied Mechanics,
Montreal, Canada (1973).
[37] “Energy Absorption Devices for Earthquake Resistant Structures,” Proceedings, 5th World Conference on
Earthquake Engineering, Rome, Italy (1973).
[38] “The Influence of a Limiting Dislocation Flux on the Mechanical Response of Polycrystalline Metals,”
International J. Solids and Structures, 10:45-59 (1974).
[39] “Continuum Description of Dislocations under Stress Reversals,” (with P.P. Gillis), J. Applied Physics,
45:1091-1096 (1974).
[40] “Thermodynamics and Dislocation Mechanics,” (with P.P. Gillis), J. Franklin Institute, 297:59-74 (1974).
[41] “Rate Dependence in Plasticity Theory,” Proceedings, 11th Annual Meeting of the Society of Engineering
Sciences, 80 (1974).
[42] “The Flexural Behavior of Fibrous Plaster Sheets,” Cement and Concrete Research, 5:347-362 (1975).
[43] “Hysteretic Dampers for Earthquake-Resistant Structures,” J. Earthquake Engineering and Structural
Dynamics, 3:287-296 (1975).
[44] “A Probabilistic Approach to Polycrystalline Plasticity,” (with S.J. Sackett and P.P. Gillis), UCRL 77397,
Lawrence Livermore Laboratory (1976).
[45] “A Dislocation Theory of Isotropic Polycrystalline Plasticity,” (with R.W. Werne), UCRL 78572, Lawrence
Livermore Laboratory (1976); also in International J. Engineering Science, 16:951-965 (1978).
3
[46] “Projectile Impact on a Thin Flexible Structure: A Singular Dynamic Contact Phenomenon,” (with G.
Dasgupta), J. Structural Mechanics, 5:19-31 (1977).
[47] “A Probabilistic Approach to Polycrystalline Plasticity, Part I: Theory,” (with S.J. Sackett), J. Franklin
Institute, 304:47-63 (1977).
[48] “Equipment-Structure Interaction at High Frequencies,” (with J.L. Sackman), Report No. DNA 4298T, Defense
Nuclear Agency, Washington, D.C. (1977).
[49] “Substructure Deletion in Finite Element Methods,” (with G. Dasgupta and J.L. Sackman), Transactions, 4th
International Conference on Structural Mechanics in Reactor Technology (SMIRT), Vol. M 4/4 (1977).
[50] “Earthquake Protection of Buildings by Natural Rubber Bearings,” (with C.J. Derham and A.G. Thomas),
Proceedings, American Chemical Society, Rubber Division, 112th Meeting, Cleveland, Ohio (1977).
[51] “Transient Analysis of Structure-Equipment Interaction,” (with J.L. Sackman), Progress Report No. 1, PR
7747, Defense Nuclear Agency, Weidlinger Associates, Menlo Park, Calif. (1977).
[52] “Earthquake Simulation Testing of a Stepping Frame with Energy-Absorbing Devices,” (with D.F. Tsztoo),
Bulletin of the New Zealand National Society for Earthquake Engineering, 10(4) (1977).
[53] “A Practical Soft Story Earthquake Isolation System,” (with J.M. Eidinger), Report No. UCB/EERC-77/27,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1977).
[54] “Natural Rubber Foundation Bearings for Earthquake Protection⎯Experimental Results,” (with C.J. Derham),
Natural Rubber Technology, 8(3) (1978).
[55] “Transient Analysis of Damped Structure-Equipment Interaction,” (with J.L. Sackman), Progress Report No.
2, PR 7812, Defense Nuclear Agency, Weidlinger Associates, Menlo Park, Calif. (1978).
[56] “Analysis of Localized Dynamic Contact on Structures Using Matched Asymptotic Expansions,” (with G.
Dasgupta), J. Structural Mechanics, 6:29-44 (1978).
[57] “Response Spectra Design Methods for Tuned Equipment-Structure Systems,” (with J.L. Sackman), J. Sound
and Vibration, 59(2):171-179 (1978).
[58] “The Development of Energy-Absorbing Devices for Aseismic Base Isolation Systems,” (with D.F. Tsztoo),
Report No. UCB/EERC-78/01, Earthquake Engineering Research Center, University of California, Berkeley,
Calif. (1978).
[59] “Experimental Results of an Earthquake Isolation System Using Natural Rubber Bearings,” (with J.M.
Eidinger), Report No. UCB/EERC-78/03, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1978).
[60] “A Seismic Isolation System for Nuclear Plant,” (with C.J. Derham), Proceedings, International Conference on
Vibration in Nuclear Plant, British Nuclear Society, Keswick, United Kingdom (1978).
[61] “A Rubber Bearing System for Seismic Protection of Structures,” (with C.J. Derham and A.G. Thomas),
Proceedings, Conference on Engineering Design for Earthquake Environments, The Institution of Mechanical
Engineers, London, United Kingdom (1978).
[62] “An Anti-Seismic Isolation System for Structures,” (with C.J. Derham), Proceedings, 6th European
Conference on Earthquake Engineering, Dubrovnik, Yugoslavia (1978).
[63] “Rational Design Methods for Light Equipment in Structures Subjected to Ground Motion,” (with J.L.
Sackman), Report No. UCB/EERC-78/19, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1978).
[64] “Dynamic Plastic Analysis Using Stress Resultant Finite Element Formulation,” (with P. Lukkunaprasit),
International J. Solids and Structures, 15:221-241 (1979).
[65] “Shock Spectra Design Methods for Equipment-Structure Systems,” (with J.L. Sackman), Shock and Vibration
Bulletin, No. 49, Part 2:171-176 (1979).
[66] “Seismic Analysis of Internal Equipment and Components in Structures,” (with J.L. Sackman), J. Engineering
Structures, 1:179-190 (1979).
4
[67] “Shock Spectra Design Methods for Internal Equipment and Components,” (with J.L. Sackman), Proceedings,
S.P.S.S. Biennial Review Conference (1979).
[68] “Aseismic Base Isolation: A Review,” Proceedings, 2nd U.S. National Conference on Earthquake Engineering,
Earthquake Engineering Research Institute, Stanford, California, 1:823-837 (1979).
[69] “Control of Seismic Response of Piping Systems and Components in Power Plants by Base Isolation,” Preprint
79-PVP-55, ASME Pressure Vessels and Piping Conference, San Francisco, Calif. (1979); also in J.
Engineering Structures, 2(3):187-198 (1980).
[70] “Testing of a Wind Restraint for Aseismic Base Isolation,” (with D.E. Chitty), Report No. UCB/EERC-78/20,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. ((1978)); also in
Engineering Structures, 2(3) (1980).
[71] “Conservatism in Summation Rules for Closely Spaced Modes,” (with J.L. Sackman), Report No. UCB/EERC-
79/11, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1979); also in
Earthquake Engineering and Structural Dynamics, 8:63-74 (1980).
[72] “Control Devices for Earthquake Resistant Design,” Proceedings, International IUTAM Symposium on
Structural Control, University of Waterloo, Edited by H.H.E. Leipholz, North Holland Pub., Amsterdam, pp.
391-413 (1979).
[73] “Equipment Response Spectra for Nuclear Power Plant Systems,” (with J.L. Sackman), Nuclear Engineering
and Design, 57:277-294 (1980)
[74] “Rate Dependent Inelastic Behavior of Polycrystalline Solids Using A Dislocation Model,” (with R.W. Werne),
Preprint 80/C2/PVP-14, ASME Pressure Vessels and Piping Conference, San Francisco, Calif. (1980).
[75] “Experimental Testing of a Friction Damped Aseismic Base Isolation System with Fail-Safe Characteristics,”
(with K.E. Beucke and M. Skinner), Report No. UCB/EERC-80/18, Earthquake Engineering Research Center,
University of California, Berkeley, Calif. (1980).
[76] “Testing of a Natural Rubber Base Isolation System by an Explosively Simulated Earthquake,” Report No.
UCB/EERC-80/25, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1980).
[77] “Safer Buildings with Rubber Bearings,” FOREFRONT, Research in the College of Engineering, University
of California, Berkeley, Calif. (1980).
[78] “The Design of Steel Energy-Absorbing Restrainers and their Incorporation into Nuclear Power Plants for
Enhanced Safety, Vol. 2; Development and Testing of Restrainers for Nuclear Piping Systems,” Report No.
UCB/EERC 80/21, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1980).
[79] “Experimental Testing of an Energy Absorbing Base Isolation System,” (with M. Skinner and K.E. Beucke),
Report No. UCB/EERC 80/35, Earthquake Engineering Research Center, University of California, Berkeley,
Calif. (1980).
[80] “Transient Analysis of Light Equipment in Structures,” (with J.L. Sackman), Proceedings, 2nd Specialty
Conference on Dynamic Response of Structures, ASCE, ed. by G. Hart, pp. 723-730, Atlanta, Georgia (1981).
[81] “Control of Seismic Response of Piping Systems and Other Structures by Base Isolation,” Report No. UCB/
EERC 81/01, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1981).
[82] “Experimental Behavior of a Spatial Piping System with Steel Energy Absorbers Subjected to a Simulated
Differential Seismic Input,” (with S.F. Stiemer and W.G. Godden), Report No. UCB/EERC-81/09, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1981).
[83] “Seismic Testing of a Neoprene Base Isolation System,” (with S.B. Hodder), Report No. UCB/EERC-81/16,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1981).
[84] “The Influence of Base Isolation on the Seismic Response of Light Secondary Equipment,” Report No. UCB/
EERC-81/17, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1981).
5
[85] “Base Isolation: Its History and Prospects,” Proceedings, World Congress of Joints, Seals and Bearing Systems
for Concrete Structures, American Concrete Institute (1981).
[86] “A Numerical Shooting Method for Solving the Vibration Problems of Beams Formulated by Continuum
Models,” (with O. Abdulkarim), J. Engineering Science, University of Riyadh, 7:1-10 (1981).
[87] “Two-dimensional Finite Elasticity Analysis of the Stability of Multilayer Elastomeric Bearings,” (with J.C.
Simo), Report No. UCB/SESM-81/06, Department of Civil Engineering, University of California, Berkeley,
Calif., (1981).
[88] “New Methods for Seismic Analysis of Secondary Systems,” (with J.L. Sackman and A. Der Kiureghian),
FOREFRONT, Research in the College of Engineering, University of California, Berkeley, Calif. (1982).
[89] “Aseismic Base Isolation,” Shock and Vibration Digest, 14(5): 17-25 (1982).
[90] “Experimental Study of Lead and Elastomeric Dampers for Base Isolation Systems in Laminated Neoprene
Bearings,” (with S.B. Hodder), Bulletin of the New Zealand National Society for Earthquake Engineering,
15(2) (1982).
[91] “Seismic Rehabilitation of Existing Buildings Using Natural Rubber Bearings,” (with D. Way), Proceedings,
1st Conference on Natural Rubber for Earthquake Protection of Buildings and Vibration Isolation, Kuala
Lumpur, Malaysia (1982).
[92] “Seismic Response of Multiply Supported Secondary Systems in Power Plant Structures,” (with A. Der
Kiureghian and J.L. Sackman), Report No. UCB/SESM-82/09, Department of Civil Engineering, University of
California, Berkeley, Calif. (1982).
[93] “The Economic Feasibility of Seismic Rehabilitation of Buildings by Base Isolation,” Report No. UCB/EERC-
83/01, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1983).
[94] “The Effect of Shear Deformation and Transverse Warping in the Non-linear Theory of Elastic Plates,” (with
J.C. Simo), Report No. UCB/SESM-83/03, Department of Civil Engineering, University of California,
Berkeley, Calif. (1983).
[95] “A Friction Damped Base Isolation System with Fail-Safe Characteristics,” (with K.E. Beucke), J. Earthquake
Engineering and Structural Dynamics, 11:33-56 (1983).
[96] “An Earthquake Isolation System for Steam Generators in Nuclear Power Plants,” (with K.S. Pister), Nuclear
Engineering and Design, 73:229-252 (1983).
[97] “Seismic Response of Torsionally Coupled Base Isolated Structures,” (with T.-C. Pan), J. Earthquake
Engineering and Structural Dynamics, 11;749-770 (1983).
[98] “Experimental Studies of Response of Piping in Multiple Structures,” (with A.D. Cowell), Proceedings, 4th
Canadian Conference on Earthquake Engineering, University of British Columbia, Vancouver, p. 151-163
(1983).
[99] “A Non-linear Damping Model for a Displacement Control System in Seismic Isolation,” (with K.E. Beucke),
Proceedings, 4th Canadian Conference on Earthquake Engineering, University of British Columbia,
Vancouver, p. 392-402 (1983).
[100] “Building Code Provision for Base Isolation,” (with G. Kost, M. Celebi and D. Way), Preprint 83-005,
American Society of Civil Engineers (1983).
[101] “A Phenomenological Penetration Model of Plates,” (with J. Liss and W. Goldsmith), International J. Impact
Engineering, 1:321-341 (1983).
[102] “The Analysis of Multilayer Elastomeric Bearings,” (with J.C. Simo), J. Applied Mechanics, 51:256-262
(1984).
[103] “Seismic Response of Base-Isolated Structures with Vertical-Rocking Coupling,” (with T.-C. Pan), J.
Earthquake Engineering and Structural Dynamics, 12:681-702 (1984).
[104] “Verification Testing of Prototype Bearings for a Base Isolated Building,” (with M. Celebi), Report No. UCB/
SESM-84/01, Department of Civil Engineering, University of California, Berkeley, Calif. (1984).
6
[105] “Rubber Mountings and Their Use in Earthquake Protection of Buildings,” (with C.J. Derham and A.G.
Thomas), Proceedings, International Rubber Conference, Moscow (1984).
[106] “Finite Element Analysis of the Stability of Multilayer Elastomeric Bearings,” (with J.C. Simo), J. Engineering
Structures, 6(3):162-174 (1984).
[107] “Seismic Response of Light Internal Equipment in Base Isolated Structures,” (with H.-C. Tsai), Report No.
UCB/SESM-84/17, Department of Civil Engineering, University of California, Berkeley, Calif. (1984).
[108] “Economic Feasibility of Seismic Rehabilitation of Existing Buildings Via Base Isolation,” (with D. Way),
Proceedings, Seismic Retrofit of Historic Buildings Conference (1984).
[109] “Modal Coupling in Base Isolated Structures,” (with T.-C. Pan), Proceedings, 8th Structural Mechanics in
Reactor Technology Congress, K 21/9 (1984).
[110] “Equivalent Linearizations for Practical Hysteretic Seismic Isolation Systems,” (with K.E. Beucke),
International J. Nonlinear Mechanics, 23:211-238 (1985).
[111] “Nonlinear Natural Rubber Bearings for Seismic Isolation,” (with C.J. Derham and A.G. Thomas), Nuclear
Engineering and Design, 84(3):417-428 (1985).
[112] “Combined Earthquake Protection and Vibration Isolation of Structures,” (with C.J. Derham), Natural Rubber
Technology, 16:3-11 (1985).
[113] “Shake Table Studies of Base-Isolated Bridge Superstructures,” (with I.G. Buckle), Proceedings, Joint U.S.-
New Zealand Workshop on Seismic Resistance of Highway Bridges, San Diego, Calif. (1985).
[114] “The Implementation of Seismic Hazard Reduction by Base Isolation,” (with M. Celebi), Proceedings, 2nd
International Conference on Soil Dynamics and Earthquake Engineering, Edited by C. Brebbia, 1-59, 1-68
(1985).
[115] “Coupled Vertical-Rocking Response of Base-Isolated Structures,” (with T.-C. Pan), Proceedings, ASCE
Specialty Conference on Structural Engineering in Nuclear Facilities, p. 5-4-1 to 5-4-19 (1985).
[116] “Fractional Derivative Representation of Seismic Response of Base-Isolated Models,” (with C.-G. Koh),
Report No. UCB/SESM-85/07, Department of Civil Engineering, University of California, Berkeley, Calif.
(1985).
[117] “Aseismic Base Isolation,” Shock and Vibration Digest, 17(7):3-14 (1985).
[118] “Earthquake Simulator Testing of a Base-Isolated Bridge Deck,” (with I.G. Buckle and H.-C. Tsai), Report No.
UCB/EERC-85/09, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1985).
[119] “Seismic Response of Light Internal Equipment in Base-Isolated Structures,” J. Earthquake Engineering and
Structural Dynamics, 13(6):711-732 (1985).
[120] “Aseismic Base Isolation: Review and Bibliography,” Soil Dynamics and Earthquake Engineering, 5(4):202-
217 (1986).
[121] “Shake Table Studies of Base Isolated Bridge Superstructures with Energy Dissipaters,” (with I.G. Buckle),
Proceedings, 8th European Conference Earthquake Engineering, Laboratorio Nacional de Engenharia Civil,
5:8.4/55-8.4/61 (1986).
[122] “Basic Concepts and Potential Applications for Base Isolation,” Proceedings, ASCE Structures Congress '86
(1986).
[123] “Anti-Seismic Rubber Bearings with Inherent Wind Restraint and Vibration Isolation Characteristics,” (with
C.J. Derham and A.G. Thomas), Proceedings, 2nd World Congress on Joints and Bearings, Vol. 1 (1986).
[124] “Properties of Slender Elastomeric Isolation Bearings During Shake Table Studies of a Large-Scale Model
Bridge Deck,” (with I.G. Buckle), Proceedings, 2nd World Congress on Joints and Bearings, Vol. 1 (1986).
[125] “A Layered Notch Filter for High-Frequency Isolation,” (with J.L. Sackman and A.E. Javid), Proceedings,
1986 Pressure Vessel and Piping and Computer Engineering Divisions Conference, Chicago, Illinois (1986).
7
[126] “Quality Assurance and Control of Fabrication for a High Damping Rubber Base Isolation System,” (with D.
Way), Proceedings, 3rd U.S. National Conference on Earthquake Engineering, Earthquake Engineering
Research Institute, 3:1911-1921 (1986).
[127] “Reduction of the Stiffness of Rubber Bearings due to Compressibility,” (with M.S. Chalhoub), Report No.
UCB/SESM-86/06, Department of Civil Engineering, University of California, Berkeley, Calif. (1986).
[128] “A Displacement Control and Uplift Restraint Device for Base Isolated Structures,” (with M.C. Griffith and
I.D. Aiken), Report No. UCB/EERC-87/03, Earthquake Engineering Research Center, University of
California, Berkeley, Calif. (1987).
[129] “The Joint Malaysian Rubber Producers’ Association - EERC Earthquake Project,” Proceedings, United
Nations Industrial Development Organization Composites Workshop, Jakarta, Indonesia (1987).
[130] “Base Isolation/Passive Control - Theoretical Aspects,” Proceedings, Structural Applications of Protective
Systems for Earthquake Hazard Mitigation, National Center for Earthquake Engineering Research, Buffalo,
New York (1987).
[131] “Recent Developments in Seismic Isolation,” Proceedings, ASME Pressure Vessel and Piping Conference,
127:381-385 (1987).
[132] “Seismic and Shock Isolation System for Modular Power Plants,” (with F.F. Tajirian), Proceedings, ASME
Pressure Vessel and Piping Conference, 127:439-444 (1987).
[133] “Base Isolation for Reinforced Concrete Structures,” (with M.C. Griffith), Proceedings, ASCE Structures
Conference, Orlando, Florida (1987).
[134] “Mechanical Characteristics of Base Isolation Bearings for a Bridge Deck Model Test,” (with I.G. Buckle and
C.-G. Koh), Report No. UCB/EERC-86/11, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1987).
[135] “Effects of Axial Load on Elastomeric Isolation Bearings,” (with C.-G. Koh), Report No. UCB/EERC-86/12,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1987).
[136] “Design Procedure for R-I Bearings,” (with N. Mostaghel), Report No. UCB/EERC-87/18, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1987).
[137] “Robust Control of Base Isolated Structures Under Earthquake Excitation,” (with A. Soldatos and G.
Leitmann), J. Optimum Theory Applications, 53(2):159-180 (1987).
[138] “Experimental Evaluation of Seismic Isolation of Medium-Rise Structures Subject to Uplift,” (with M. C.
Griffith, V. A. Coveney and C.-G. Koh), Report No. UCB/EERC-88/02, Earthquake Engineering Research
Center, University of California, Berkeley, Calif. (1988).
[139] “Earthquake Simulator Testing of a Combined Sliding Bearing and Rubber Bearing Isolation System,” (with
M. S. Chalhoub), Report No. UCB/EERC-87/04, Earthquake Engineering Research Center, University of
California, Berkeley, Calif., (1988).
[140] “Earthquake Simulator Evaluation of a Combined Sliding Bearing Rubber Bearing Isolation System,” (with
M.S. Chalhoub), Proceedings, Vibrations Chocs '88, Groupement pour l'Avancement de la Mecanique
Industrielle (G.A.M.I.), Lyon, France (1988).
[141] “Earthquake Simulator Tests of a Neoprene Base Isolation System,” (with M. C. Griffith and I. D. Aiken),
Proceedings, 2nd Symposium on Seismic, Shock and Vibration Isolation, Pittsburgh, Penn, ASME Pressure
Vessel and Piping Conference, ASME PVP-147, pp. 35-43 (1988).
[142] “Evaluation of Nonlinear Response in Seismically-Isolated Buildings,” (with C.A. Kircher, B. Lashkari, and
R. Mayes), Proceedings, 2nd Symposium on Seismic, Shock and Vibration Isolation, Pittsburgh, Penn., ASME
Pressure Vessel and Piping Conference, ASME PVP-147, pp. 71-81 (1988).
[143] “Earthquake Simulator Testing of Cylindrical Water Tanks in Base Isolated Buildings,” (with M.S. Chalhoub),
Proceedings 2nd Second Symposium on Seismic, Shock and Vibration Isolation, Pittsburgh, Penn., ASME
Pressure Vessel and Piping Conference, ASME PVP-147, pp. 51-64 (1988).
[144] “Design Procedure for R-I Bearings,” (with N. Mostaghel and A.R. Mortazavi), Report No. UTEC 88-031,
University of Utah, Department of Civil Engineering, Salt Lake City, Utah (1988).
8
[145] “Seismic Isolation for a Modular Liquid Metal Reactor Concept (PRISM),” (with E.L. Gluekler and F.F.
Tajirian), Proceedings, ANS Topical Meeting on Safety of Next Generation Power Reactors, Seattle,
Washington (1988).
[146] “Testing of Seismic Isolation Bearings for Advanced Liquid Metal Reactor-Prism,” (with F.F. Tajirian),
Proceedings, 2nd Symposium on Seismic, Shock and Vibration Isolation, Pittsburgh, Penn., ASME Pressure
Vessel and Piping Conference, ASME PVP-147 (1988).
[147] “Experimental Study of Friction Damping for Steel Frame Structures,” (with I.D. Aiken), Proceedings, 2nd
Symposium on Seismic, Shock and Vibration Isolation, Pittsburgh, Penn., ASME Pressure Vessel and Piping
Conference, ASME PVP-147(1988).
[148] “A Simplified Model for Elastomeric Isolation Bearings,” (with C.-G. Koh), Proceedings, 25th Annual
Technical Meeting, Society of Engineering Science, Berkeley, Calif. (1988).
[149] “Non-Classical Damping in Dynamic Analysis of Base Isolated Structures with Internal Equipment,” (with H.-
C. Tsai), Earthquake Engineering and Structural Analysis, 16:29-44 (1988).
[150] “Effect of Target Bending in Normal Impact of a Flat-Ended Cylindrical Projectile,” (with S.T. Jeng and W.
Goldsmith), International J. Solids and Structures, 24(12):1243-1266 (1988).
[151] “A Simple Mechanical Model for Elastomeric Bearings used in Base Isolation,” (with C.-G. Koh),
International J. Mechanical Science, 30(12):933-943 (1988).
[152] “Experimental Evaluation of Seismic Isolation of a Nine-Story Braced Steel Frame Subject to Uplift,” (with
M.C. Griffith and I.D. Aiken), Report No. UCB/EERC-88/05, Earthquake Engineering Research Center,
University of California, Berkeley, Calif. (1988).
[153] “Earthquake Engineering Research at Berkeley⎯1988: Seismic Response of a Nine-Story Steel Frame with
Friction Damped Cross-Bracing,” (with I.D. Aiken and A.S. Pall), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1988).
[154] “Earthquake Engineering Research at Berkeley⎯1988: Effect of Initial Conditions and Computational
Algorithm on Long Period Response Spectra,” (with R. Blazquez), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1988).
[155] “Earthquake Engineering Research at Berkeley⎯1988: Shaking Table Evaluation of Strong Motion Data
Processing Techniques,” (with J.M. Blondet and J.F. Yep), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1988).
[156] “Earthquake Engineering Research at Berkeley⎯1988: Earthquake Simulator Testing of Cylindrical Water
Tanks in Base Isolated Structures,” (with M.S. Chalhoub), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif., (1988).
[157] “Earthquake Engineering Research at Berkeley⎯1988: A Displacement Control and Uplift Restraint Device
for Base Isolated Structures,” (with M.C. Griffith and I.D. Aiken), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1988).
[158] “Earthquake Engineering Research at Berkeley⎯1988: Combining Sliders and Tension Controlled
Elastomeric Bearings for Base Isolation,” (with M.S. Chalhoub), Report No. UCB/EERC-88/17, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1988).
[159] “Recent Developments in the Testing of Base Isolation Systems,” (with I.D. Aiken), Proceedings, '88
Structures Congress of the American Society of Civil Engineers, San Francisco, Calif. (1988).
[160] “Seismic Isolation of Nuclear Plants: A World Overview,” (with F.F. Tajirian), Proceedings, '88 Structures
Congress of the American Society of Civil Engineers, San Francisco, Calif. (1988).
[161] “Base Isolation in Japan,” Report No. UCB/EERC-88/20, Earthquake Engineering Research Center, University
of California, Berkeley, Calif. (1989).
[162] “A Simplified Model for Elastomeric Isolation Bearings,” (with C.-G. Koh), Proceedings, 1st Pan- American
Congress of Applied Mechanics, Rio de Janeiro, Brazil (1989).
[163] “Compression Stiffness of Bonded Square Layers of Nearly Incompressible Material,” (with C.-G. Koh), J.
Engineering Structures, 11(1):9-15 (1989).
9
[164] “Viscoelastic Stability Model for Elastomeric Isolation Bearings,” J. Structural Engineering, 115(2):285-302
(1989).
[165] “A Layered Notch Filter for High Frequency Dynamic Isolation,” (with J.L. Sackman and A.E. Javid), J.
Pressure Vessel Technology, 111:17-24 (1989).
[166] “The Development and Testing of Seismic Isolation Systems for Advanced Reactors,” (with F.F. Tajirian),
Proceedings, International Symposium on Pressure Vessel Technology and Nuclear Codes and Standards,
Seoul, Korea (1989).
[167] “The Economic Feasibility of Seismic Rehabilitation of Buildings by Base Isolation,” Proceedings,
International Meeting on Base Isolation and Passive Energy Dissipation, Assisi, Italy, p. 3.01-3.16 (1989).
[168] “Experimental Studies of the Seismic Response of Structures Incorporating Base Isolation Systems,” (with I.D.
Aiken), Proceedings, International Meeting on Base Isolation and Passive Energy Dissipation, Assisi, Italy, p.
19.01-19.09 (1989).
[169] “Seismic Response of the Superstructure and Attached Equipment in a Base-Isolated Building,” (with H.-C.
Tsai), J. Earthquake Engineering and Structural Dynamics, 18(4):551-564 (1989).
[170] “Applicability of the Southwell Plot to Shear Deformable Columns,” (with C.-G. Koh), J. Testing and
Evaluation (1989).
[171] “Dynamic Parameter Identification for Non-Linear Isolation Systems in Response Spectrum Analysis,” (with
H.-C. Tsai), J. Earthquake Engineering and Structural Dynamics, 18(8):1119-1132 (1989).
[172] “Seismic Isolation Development for the U.S. Advance Liquid-Metal Reactor Program,” (with E.L. Gluekler,
C.C. Bigelow, V. DeVita, R.W. Seidensticker and F.F. Tajirian), Proceedings, 10th International Conference
on Structural Mechanics in Reactor Technology (SMiRT-10), Post Conference Seminar No. 1: Seismic Base
Isolation of Nuclear Power Facilities, San Francisco, Calif., pp. 113-125 (1989).
[173] “Experimental Studies of the Seismic Response of Structures Incorporating Base-Isolation Systems,” (with I.D.
Aiken), Proceedings, 10th International Conference on Structural Mechanics in Reactor Technology (SMiRT-
10), Post-Conference Seminar No. 1: Seismic Base Isolation of Nuclear Power Facilities, San Francisco, Calif.,
p. 176-196 (1989).
[174] “Mechanics of Low Shape Factor Elastomeric Seismic Isolation Bearings,” (with I.D. Aiken and F.F. Tajirian),
Report No. UCB/EERC-89-13, Earthquake Engineering Research Center, University of California, Berkeley,
Calif. (1989).
[175] “Non-Linear Material Modeling of Isolation Bearings,” (with K.D. Papoulia), Proceedings, 2nd National
Congress on Mechanics, Hellenic Society for Theoretical and Applied Mechanics, Athens, Greece (1989).
[176] “Comparison of Earthquake Simulator Test Results with the SEAONC Tentative Seismic Isolation Design
Requirements,” (with M.C. Griffith and I.D. Aiken), Earthquake Spectra, 6(2):403-417 (1990).
[177] “Application of Fractional Derivatives to Seismic Analysis of Base-Isolated Models,” (with C.-G. Koh), J.
Earthquake Engineering and Structural Dynamics, 19:229-241 (1990).
[178] “Comparison of SEAONC Base Isolation Tentative Code to Shake Table Tests,” (with M.S. Chalhoub), J.
Structural Engineering, 116(4):925-938 (1990).
[179] “Displacement Control and Uplift Restraint for Base-Isolated Structures,” (with M.C. Griffith and I.D. Aiken),
J. Structural Engineering, 116(4):1135-1148 (1990).
[180] “Effect of Bulk Compressibility on the Stiffness of Cylindrical Base Isolation Bearings,” (with M.S.
Chalhoub), International J. Solids and Structures, 26(7):743-760 (1990).
[181] “Base Isolation: Linear Theory and Design,” Earthquake Spectra, 6(2):223-244 (1990).
[182] “Seismic Isolation for Advanced Nuclear Power Stations,” (with F.F. Tajirian and I.D. Aiken), Earthquake
Spectra, 6(2):371-401 (1990).
[183] “The Application of Viscoelastic Dampers to Seismically Resistant Structures,” (with I.D. Aiken and P.
Mahmoodi), Proceedings, 4th U.S. National Conference on Earthquake Engineering, 3:459-468 (1990).
10
[184] “Mechanics of High-Shape Factor Elastomeric Seismic Isolation Bearings,” (with I.D. Aiken and F.F.
Tajirian), Report No. UCB/EERC-90/01, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1990).
[185] “Javid's Paradox: The Influence of Preform on the Modes of Vibrating Beams,” (with J.L. Sackman and A.
Javid), Report No. UCB/EERC-90/02, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1990).
[186] “Earthquake Simulator Tests of Viscoelastic Dampers for Medium Rise Structures,” (with I.D. Aiken), Report
No. UCB/EERC-90-03, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1990).
[187] “Shake Table Test of Cylindrical Water Tanks in Base-Isolated Structures,” (with M.S. Chalhoub), J.
Engineering Mechanics, 116(7):1451-1472 (1990).
[188] “Sliders and Tension Controlled Reinforced Bearings Combined for Earthquake Isolation,” (with M.S.
Chalhoub), J. Earthquake Engineering and Structural Dynamics, 19(3):333-358 (1990).
[189] “The EDR-Energy Dissipating Restraint, A New Device for Mitigating Seismic Effect,” (with P.J. Richter, D.
Nims and R.M. Kallenbach), Proceedings, Structural Engineers Association of California Convention, Lake
Tahoe, Calif. (1990).
[190] “Experimental Study of Alternate Supports Systems for the Seismic Restraint of Piping,” (with D. Nims),
Proceedings, Advanced Technology Council ATC-29 Seismic Design and Performance of Equipment and
Nonstructural Elements in Buildings and Industrial Structures - Seminar and Workshop (1990).
[191] “Earthquake Simulator Testing of Two Damping Systems for Multistory Structures,” (with I.D. Aiken),
Proceedings, Damping '91 Conference, San Diego, Calif., FCA-1 - FCA-13 (1991).
[192] “Constitutive Modeling of Nonlinear Damping Materials,” (with J.L. Sackman and A.E. Javid), Proceedings,
Damping '91 Conference, San Diego, Calif., EBC-1 - EBC-15 (1991).
[193] “Response of Base-Isolated Structures in Recent Californian Earthquakes,” (with I.D. Aiken and P. Clark),
Proceedings, Seminar on Seismological and Engineering Implications of Recent Strong-Motion Data, Strong
Motion Instrumentation Program, California Dept. of Conservation, Sacramento, Ca., pp. 12-1 - 12-10 (1991).
[194] “Recent Experimental Studies of Isolation Systems for Nuclear and Civil Structures,” Proceedings,
International Meeting on Earthquake Protection of Buildings, Ancona, Italy, pp. 33/C-56/C (1991).
[195] “Earthquake Simulator Testing of Absorbing Systems for Multistory Structures,” (with I.D. Aiken),
Proceedings, International Meeting on Earthquake Protection of Buildings, Ancona, Italy, p. 3/D-20/D (1991).
[196] “Experimental Studies of the Seismic Response of Structures Incorporating Base-Isolation Systems,” (with I.D.
Aiken), Nuclear Engineering and Design, North-Holland, Elsevier Science Publishers (1991).
[197] “A Long-Period Isolation System Using Low-Modulus High-Damping Isolators for Nuclear Facilities at Soft-
Soil Sites,” Report No. UCB/EERC-91/03, Earthquake Engineering Research Center, University of California,
Berkeley, Calif. (1991).
[198] “Modeling of Seismic Isolation Bearings Including Shear Deformation and Stability Effects,” (with C.-G.
Koh), Applied Mechanics Review, 42(11):S113-S120 (1989).
[199] “Dynamic and Failure Characteristics of Bridgestone Bearings,” Report No. UCB/EERC-91-04, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1991).
[200] “Predictive Control of Base Isolated Structures,” (with J.A. Inaudi, F. Lopez-Almansa, and J. Rodellar), J.
Earthquake Engineering and Structural Dynamics, 21(6):471-482 (1992).
[201] “Experience in the Design and Implementation of Seismically Isolated Buildings,” Proceedings, ACEM
Seminar on Natural Rubber in Engineering, Kuala Lumpur (1991).
[202] “Natural Rubber in Vibration and Seismic Isolation,” Proceedings, ACEM Seminar on Natural Rubber in
Engineering, Kuala Lumpur (1991).
[203] “Shear Deformation and the Buckling of Columns,” Applied Mechanics Review, 44(11):S160-S165 (1991).
11
[204] “A Constitutive Model and Numerical Simulation of Elastomers at Finite Strains,” (with K.D.P. Papoulia),
Proceedings, First U.S. National Congress on Computational Mechanics, Chicago, Illinois (1991).
[205] “Viscoelastic Analysis of Isolation Bearings,” (with K.D.P. Papoulia), Proceedings, International Conference
on Computational Engineering Science, Melbourne, Australia, August (1991).
[206] “Experimental and Analytical Studies of Two Energy-Absorbing Systems for Multistory Structures,” (with I.D.
Aiken), Transactions, 11th International Conference on Structural Mechanics in Reactor Technology (SMiRT
11), K:145-150 (1991).
[207] “Shake Table Tests of Long Period Isolation System for Nuclear Facilities at Soft-Soil Sites,” Transactions,
11th International Conference on Structural Mechanics in Reactor Technology (SMiRT 11), K:193-198
(1991).
[208] “Mechanical and Failure Characteristics of High Damping, Natural Rubber Isolation Bearings of Four
Different Test Programs,” Proceedings, 11th International Conference on Structural Mechanics in Reactor
Technology (SMiRT 11), Post-SMiRT Conference Seminar No. 1: Seismic Isolation of Nuclear and Non-
Nuclear Structures, Japan (1991).
[209] “Analysis of Infinite-Strip-Shaped Base Isolator with Elastomer Bulk Compression,” (with M.S. Chalhoub), J.
Engineering Mechanics, 117(8):1791-1805 (1991).
[210] “Active Control and Seismic Isolation,” (with J.-P. Pu), J. Engineering Mechanics, 117(10):2221-2236 (1991).
[211] “The Influence of Preform on the Modes of Vibrating Beams,” (with J.L. Sackman and A. Javid), J. Earthquake
Engineering and Structural Dynamics, 20(12):1145-1157 (1991).
[212] “Active Isolation,” (with J.A. Inaudi), Proceedings, U.S. National Workshop on Structural Control Research,
Los Angeles, pp. 125-130, (1990).
[213] “A Formulation of Predictive Control for Base-Isolated Structures,” (with J.A. Inaudi, F. Lopez-Almansa, and
J. Rodellar), Proceedings, Eighth VPI&SU on Dynamics and Control of Large Structures, Blacksburg,
Virginia (1991).
[214] “A Simple Active Isolation Scheme,” (with J.A. Inaudi), Proceedings, Eighth VPI&SU on Dynamics and
Control of Large Structures, Blacksburg, Virginia (1991).
[215] “Earthquake Simulator Testing of a Combined Sliding Bearing and Rubber Bearing Isolation System,” (with
M. S. Chalhoub), Report No. UCB/EERC-87/04, Earthquake Engineering Research Center, University of
California, Berkeley, Calif. (1990).
[216] “Analysis of Compression of Hollow Circular Elastomeric Bearings,” (with M.C. Constantinou and A.
Kartoum), J. Engineering Structures, 14(2):103-111 (1992).
[217] “Stability of R-I Bearings: Analysis and Experiment”, (with N. Mostaghel and P.W. Clark), Earthquake
Spectra, 8(2):259-277 (1992).
[218] “Rubber Bearings for the Earthquake Protection of Buildings,” Proceedings, Rubbercon 92, Brighton, United
Kingdom, pp. 305-310 (1992).
[219] “The Current Status of Seismic Isolation Technology in the United States,” Proceedings, IAEA Specialists'
Meeting on Seismic Isolation Technology, San Jose, Calif. (1992).
[220] “Comparative Study of Four Passive Energy Dissipation Systems,” (with I.D. Aiken and D.K. Nims), Bulletin
of the New Zealand National Society for Earthquake Engineering, 25(3):175-192 (1992).
[221] “Optimum Damping in Base-Isolated Structures,” (with J.A. Inaudi), Proceedings, 10th World Conference on
Earthquake Engineering, Madrid, 4:1993-1998 (1992).
[222] “The Implementation of Base Isolation in the United States,” Invited Keynote Address, Post-Conference
Publication, 10th World Conference on Earthquake Engineering, Madrid, (1992).
[223] “Experimental Studies of the Mechanical Characteristics of Three Types of Seismic Isolation Bearings,” (with
I.D. Aiken, P.W. Clark, K. Tamura, M. Kikuchi and T. Itoh), Proceedings, 10th World Conference on
Earthquake Engineering, Madrid, 4:2281-2286 (1992).
12
[224] “Optimal Design of Seismic Isolation for Multistoried Buildings,” (with F.L. Zhou, K.N.G. Fuller and T.-C.
Pan), Proceedings, 10th World Conference on Earthquake Engineering, Madrid, 4:2449-2454 (1992).
[225] “Control Activo de Etructuras con Aislamiento de Base,” (in Spanish) (with J.A. Inaudi), Revista Internacional
de Metodos Numericos para Calculo y Diseno en Ingenieria, 8(2):177-190 (1992).
[226] “Mechanical Characteristics of Neoprene Isolation Bearings,” (with E. Quiroz), Report No. UCB/EERC-92/11,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1992).
[227] “Application of a Mass Damping System to Bridge Structures,” (with K. Hasegawa), Report No. UCB/EERC-
92/12, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1992).
[228] “A Friction Mass Damper for Vibration Control,” (with J.A. Inaudi), Report No. UCB/EERC-92/15,
Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1992).
[229] “Hybrid Isolation Systems for Equipment Protection,” (with J.A. Inaudi), J. Earthquake Engineering and
Structural Dynamics, 22(4):297-313 (1993).
[230] “Minimum Variance Control of Base-Isolated Floors,” (with J.A. Inaudi), J. Structural Engineering,
119(2):438-453 (1993).
[231] “State-of-the-Art and State-of-the-Practice in Base Isolation,” Proceedings, ATC-17-1 Seminar on Seismic
Isolation, Passive Energy Dissipation and Active Control, 1:9-28 (1993).
[232] “Design- and Ultimate-Level Earthquake Tests of a 1/2.5-Scale Base-Isolated Reinforced-Concrete Building,”
(with I.D. Aiken, P.W. Clark, M. Kikuchi, M. Saruta and K. Tamura), Proceedings, ATC-17-1 Seminar on
Seismic Isolation, Passive Energy Dissipation and Active Control, 1:281-292 (1993).
[233] “Code Requirements for the Design and Implementation of Passive Energy Dissipation Systems,” (with A.S.
Whittaker, I.D. Aiken, D. Bergman, P.W. Clark, J. Cohen and R. Scholl, Proceedings, ATC-17-1 Seminar on
Seismic Isolation, Passive Energy Dissipation and Active Control, 1:497-508, (1993).
[234] “Statistical Linearization Method in the Preliminary Design of Structures with Energy Dissipating Devices,”
(with J.A. Inaudi and C.S.W. To), Proceedings, ATC-17-1 Seminar on Seismic Isolation, Passive Energy
Dissipation and Active Control, 2:509-520 (1993).
[235] “Applications of the Energy Dissipating Restraint to Buildings,” (with D.K. Nims, J.A. Inaudi and P.J. Richter),
Proceedings, ATC-17-1 Seminar on Seismic Isolation, Passive Energy Dissipation and Active Control, 2:627-
638 (1993).
[236] “Optimal Control of Sliding Base Isolation Structures,” (with J.A. Inaudi and J.-P. Pu), Proceedings, ATC-17-
1 Seminar on Seismic Isolation, Passive Energy Dissipation and Active Control, 2:787-798 (1993).
[237] “Recent Developments in Seismic Isolation Technology,” Proceedings, ASCE Structures Congress '93, 1:181-
186 (1993).
[238] “Large-Scale Earthquake Simulator Study of the Tohoku University Base-Isolated Building,” (with P.W. Clark
and I.D. Aiken), Proceedings, ASCE Structures Congress '93, 1:736-741 (1993).
[239] “3-D Hybrid Control of Buildings Under Wind Excitation,” (with J.-P. Pu), Proceedings, Infrastructure '91,
Hong Kong, pp. 135-145 (1991).
[240] “Nonlinear Mass Dampers for Vibration Reduction,” (with J.A. Inaudi), Proceedings, Ninth VPI&SU
Symposium, Blacksburg, Virginia (1993).
[241] “Analytical and Experimental Study of a Tuned-Mass Damper Using Shape Memory Alloys,” (with J.A.
Inaudi, W. Taniwangsa and R. Krumme), Proceedings, Damping 93, HAA-1-HAA-19, San Francisco (1993).
[242] “On the Linearization of Structures Containing Linear-Friction Dissipating Devices,” (with J.A. Inaudi),
Proceedings, Damping 93, FCB-1-FCB-20, San Francisco (1993).
[243] “The Application of Seismic Isolation for the Retrofit of Historic Buildings,” Proceedings, Colloquium on
Seismic Stabilization of Historic Buildings, The Getty Conservation Institute, Quito, Ecuador (1993).
[244] “Application of Shape Memory Materials for Reduction of Structural Response to Earthquake Ground
Motion,” Proceedings, Workshop on Smart and High Performance Materials and Structures, Tsukuba, Japan
(1993).
13
[245] “Natural Rubber Bearings for Earthquake Protection of Buildings,” Natural Rubber, Current Developments in
Product Manufacture and Applications, ed. Abdul Aziz S.A. Kadir, Rubber Research Institute of Malaysia,
Kuala Lumpur (1993).
[246] “Optimum Damping in Linear Isolation Systems,” (with J.A. Inaudi), J. Earthquake Engineering and
Structural Dynamics, 22(7):583-598 (1993).
[247] “Recent Developments on Isolation of Civil Buildings in the United States,” Proceedings, International Post-
SMiRT Conference on Isolation, Energy Dissipation and Control of Vibrations of Structures, Capri, Italy
(1993) pp. 173-189.
[248] “Limites de Performance de Estructuras con Aislamiento Pasivo Y Activo,” (with J.A. Inaudi), Proceedings, Il
Congress de Metodos Numericos en Ingeniera, Spain, 1:233-242 (1993).
[249] Earthquake-Resistant Design with Rubber, Springer-Verlag, London (1993).
[250] “Variable-Structure Homogeneous Control Systems,” (with J.A. Inaudi), Proceedings, International Workshop
on Structural Control, Hawaii, 1993, (Eds. S. Masri and G. Housner), University of Southern California.
[251] “Testing of Passive Energy Dissipation Systems,” (with I.D. Aiken, D.K. Nims and A.S. Whittaker),
Earthquake Spectra, 9(3):335-370 (1993).
[252] “A Robust Delay Compensation Technique Based on Memory,” (with J.A. Inaudi), Earthquake Engineering
& Structural Dynamics, 23(9):987-1001 (1994).
[253] “Single-Degree-of-Freedom Nonlinear Homogeneous Systems,” (with J.A. Inaudi and G. Leitmann), J.
Engineering Mechanics, 120(7):1543-1562 (1994).
[254] “The Implementation of Base Isolation in the United States,” Proceedings, 6th Symposium on Seismic, Shock,
and Vibration Isolation, ASME Pressure Vessel and Piping Conference, Denver, Colorado (1993).
[255] “The Use of Natural Rubber for the Earthquake Protection of Buildings,” Proceedings, International Rubber
Conference, Orlando, Florida (1993).
[256] “Mass Damper Using Friction-Dissipating Devices,” (with J.A. Inaudi), J. Engineering Mechanics,
121(1):142-149 (1995).
[257] “Modal Equations of Linear Structures with Viscoelastic Dampers,” (with J.A. Inaudi), short communication,
Earthquake Engineering & Structural Dynamics, 24(1):145-151 (1995).
[258] “Linear-Friction Dissipators for Truss Structures,” (with J.A. Inaudi and D.K. Nims), Proceedings, Smart
Structures and Materials Conference 94, Orlando, Florida (1994).
[259] “On the Accuracy of the Modal Strain Energy Method,” (with A. Zambrano and J.A. Inaudi), Proceedings,
Smart Structures and Materials Conference 94, Orlando, Florida (1994).
[260] “Compression of Bonded Blocks of Soft Elastic Material: Variational Solution,” (with K.D. Papoulia), J.
Engineering Mechanics, 122(2):163-170 (1996).
[261] “On the Analysis of Structures with Viscoelastic Dampers,” (with J.A. Inaudi and A. Zambrano), Report No.
UCB/EERC-93/06, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1993).
[262] “A Methodology for Design of Viscoelastic Dampers in Earthquake-Resistant Structures,” (with H. Abbas),
Report No. UCB/EERC-93/09, Earthquake Engineering Research Center, University of California, Berkeley,
Calif. (1993).
[263] “Material Characterization of Elastomers Used in Earthquake Base Isolation,” (with K.D. Papoulia), Report
No. UCB/EERC-90-18, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1990).
[264] “The Tests of Natural Rubber Isolators for the UNIDO Demonstration Building in Shantou City, Guangdong
Province, P.R. China,” Proceedings, International Workshop on the Use of Rubber-Based Bearings for the
Earthquake Protection of Small Buildings, Shantou City, P.R. China (1994).
[265] “Recent Developments on Isolation Systems and Passive Energy Dissipators for Seismic Design,”
Proceedings, Kerensky Conference, Singapore (1994).
14
[266] “Small-Scale Testing of a Self-Centering Friction Energy Dissipator for Structures,” (with D.K. Nims), Report
No. UCB/EERC-94-06, Earthquake Engineering Research Center, University of California, Berkeley, Calif.
(1994).
[267] “Experimental Verification of the Seismic Effectiveness of TMD’s with Viscoelastic Materials,” (with J.A.
Inaudi, F. Lopez-Almansa, D. Foti and H. Khechfe), Earthquake Resistant Construction and Design, Savidis
(Eds.), Balkema, Rotterdam (1994).
[268] “Earthquake Simulator Test of a Base-Isolated Reinforced Concrete Building,” (with M. Kikuchi, M. Saruta,
K. Tamura, I.D. Aiken and P.W. Clark), J. Structural Construction Engineering, Architectural Institute of
Japan, 462:69-78 (August 1994).
[269] “Performance of Seismically Isolated Structures in the January 17, 1994 Northridge Earthquake,” (with P.W.
Clark and M. Higashino), Proceedings, 6th U.S. Japan-Workshop on Improvement of Structural Design and
Construction Practices., Applied Technology Council, ATC-15-5, Victoria, B.C., (1994).
[270] “The Development of Isolators and Isolation Components for Earthquake-Resistant Design,” (Ed. J. Duma)
Proceedings, 10th European Conference on Earthquake Engineering, Vienna, 3:1863-1868 (1994).
[271] “Experimental and Analytical Studies of Shape Memory Alloy Dampers for Structural Control,” (with P.W.
Clark, I.D. Aiken, M. Higashino and R.C. Krumme), Proceedings, 1995 Conference on Smart Structures and
Materials, San Diego, Calif. (1995).
[272] “The Influence of Plate Flexibility on the Buckling Load of Elastomeric Isolators,” Report No. UCB/EERC-94/
03, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (1994).
[273] “Experiments on Tuned Mass Dampers Using Viscoelastic Frictional and Shape-Memory Alloy Materials,”
(with J.A. Inaudi), Proceedings, 1st World Conference on Structural Control, 2: TP3-127 -136, Los Angeles,
Calif. (1994).
[274] “Macroscopic Models with Complex Coefficients and Causality,” (with N. Makris and J.A. Inaudi) J.
Engineering Mechanics, 122(6):566-573 (1996).
[275] “Tests of Reduced-Scale Seismic Isolation Bearings for the U.S.-Advanced Liquid Metal Reactor (ALMR)
Program,” (with P.W. Clark, I.D. Aiken, E.L. Gluekler and F.F. Tajirian), Proceedings, Joint ASME/JSME
Pressure Vessels and Piping Conference, Seismic Shock and Vibration Isolation, Honolulu, Hawaii, PVP-Vol
319, pp. 303-308 (July 1995).
[276] “Safety Evaluation and Hazard Mitigation of the Los Angeles City Hall,” (with H.A. Sassi and S.F. Masri),
Proceedings, Joint ASME/JSME Pressure Vessels and Piping Conference, Seismic Shock, and Vibration
Isolation, Honolulu, Hawaii, PVP-319:249-254 (July 1995).
[277] “Seismic Isolation - A Case Study of Research Into Practice in the Field of Earthquake Engineering,” (with I.D.
Aiken), Proceedings, First National Conference and Workshop on Research into Practice, National Science
Foundation, Crystal City, Virginia (1995).
[278] “Linear Hysteretic Damping and the Hilbert Transform,” (with J.A. Inaudi), J. Engineering Mechanics,
121(5):626-632 (1995).
[279] “Modal Coupling and Accuracy of Modal Strain Energy Method,” (with A. Zambrano and J.A. Inaudi), J.
Engineering Mechanics, 122(7):603-612 (1996).
[280] “Final Report on the International Workshop on the Use of Rubber-Based Bearings for the Earthquake
Protection of Buildings,” Report No. UCB/EERC-95-05, Earthquake Engineering Research Center, University
of California, Berkeley, Calif. (1995).
[281] “New Applications and R&D for Isolated Civil Buildings in the United States,” Proceedings, Post-Smirt
Conference on Seismic Isolation, Passive Energy Dissipation and Control of Vibrations of Structures,
Santiago, Chile (August 1995).
[282] “New R&D for Isolated Nuclear Facilities in the U.S.A.,” (with E.L. Gluekler, P.W. Clark, I.D. Aiken and F.F.
Tajirian), Proceedings, Post-Smirt Conference on Seismic Isolation, Passive Energy Dissipation and Control
of Vibrations of Structures, Santiago, Chile (August 1995).
15
[283] “Passive Control Systems for Mitigation of Near-Field Earthquake Ground Motions,” (with P.W. Clark),
Proceedings, ASCE International Conference and Exposition on Natural Disaster Reduction, Washington,
D.C. (March 1996).
[284] “Energy-Based Modeling of High-Damping Rubber Isolators for Dynamic Analysis.” (with P.W. Clark),
Proceedings, ASCE Structures Congress XIV, Chicago (April 1996).
[285] “Experimental Study of Mechanical Pipe Snubber Seismic Behavior,” (with D.K. Nims), ASME J. Pressure
Vessel Technology, 119(3):384-388 (August 1997).
[286] “Viscoelastic Damper Overview for Seismic and Wind Applications,” (with E.J. Nielsen and M.L. Lai),
Proceedings, 1996 Symposium on Smart Structures and Materials. San Diego, Calif. (February 1996).
[287] “Heat Generation Effects on Viscoelastic Dampers in Structures,” (with J.A. Inaudi, M. Blondet, and A.
Aprile), Proceedings, 11th World Conference on Earthquake Engineering, Acapulco, Mexico (July 1996).
[288] “Studies on Seismic Isolation for Housing in Developing Regions,” (with W. Taniwangsa), Proceedings, 11th
World Conference on Earthquake Engineering, Acapulco, Mexico (July 1996).
[289] “Nonlinear Homogeneous Dynamical System,” (with J.A. Inaudi), Report No. UCB/EERC-93-11, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (1995).
[290] “Dynamics of Homogeneous Frictional Systems,” (with J.A. Inaudi), Dynamics with Friction: Modeling,
Analysis and Experiment, Vol. 7, Chapter 3, ed. A. Guran, F. Pfeiffer, and K. Popp, World Scientific Publishing
Co., Singapore (1996).
[291] “Reduction of Structural Response by Energy Dissipation Devices Modeled on Shape Memory Materials,”
(with C.W.S. To), Proceedings, ASCE 11th Engineering Mechanics Conference, Fort Lauderdale, Florida
(May 1996).
[292] “Random Responses of Discretized Structures with Energy Dissipation Devices,” (with C.W.S. To and M.L.
Liu), Proceedings, ASCE 11th Engineering Mechanics Conference, Fort Lauderdale, Florida (May 1996).
[293] “Natural Rubber Isolation Systems for Earthquake Protection of Low-Cost Buildings,” Report No. UCB/
EERC-95-12, Earthquake Engineering Research Center, University of California, Berkeley, Calif. (June 1996).
[294] “Experimental and Analytical Studies of Base Isolation Applications for Low-Cost Housing,” (with W.
Taniwangsa), Report No. UCB/EERC-96-04, Earthquake Engineering Research Center, University of
California, Berkeley, Calif. (July 1996).
[295] “The Evolution and Acceptance of Seismic Isolation in the United States,” RE Magazine, Building
Maintenance and Management Centre of Japan, 17(6):32-41 (1996).
[296] Earthquake-Resistant Design with Rubber, 2nd ed., Springer-Verlag, London (1996).
[297] “Experimental Analysis of a Model Isolated at the Base with Rubber-Layer Roller Bearings,” (with D. Foti),
European Earthquake Engineering, 10(2):3-13 (1996).
[298] "Performance of Seismically Isolated Structures in the January 17, 1994 Northridge Earthquake", (with Clark,
P.W., Highashino, M.). Procs. of the Sixth U.S.-Japan Workshop on the Improvement of Building Structural
Design and Construction Practices in the United States and Japan (1996). Victoria, B.C., Canada: Applied
Technology Council and Japan Structural Consultants Association, ATC-15-5.
[299] “Evolutionary Model of Viscoelastic Dampers for Structural Applications,” (with A. Aprile and J.A. Inaudi),
Journal of Engineering Mechanics, 123(6):551-560 (June 1997).
[300] “Visco-Hyperelastic Model for Filled Rubbers in Vibration Isolation,” (with K.-D. Papoulia), Journal of
Engineering Materials and Technology (ASME), Vol. 119 (July 1997).
[301] “Stability of Isolators at Large Horizontal Displacements,” (with M. Imbimbo), J. Earthquake Spectra,
13(3):415-430 (1997).
[302] “Stability Aspects of Elastomeric Isolators,” (with M. Imbimbo), J. Earthquake Spectra, 13(3):431-449 (1997).
[303] “New Applications and R&D for Isolated Buildings in the United States,” Proceedings, Post-SMiRT
Conference on Seismic Isolation, Passive Energy Dissipation and Control of Vibrations of Structures,
Taormina, Italy (August 1997).
16
[304] “Experimental Testing of Reduced-Scale Seismic Isolation Bearings for Nuclear Application,” (with I.D.
Aiken and P.W. Clark,) Proceedings, 2nd RCM of the International Atomic Energy Agency, Taormina, Italy
(August 1997).
[305] “Experimental Study of a Reduced Scale Model Seismically Base Isolated with Rubber-Layer Roller Bearings
(RLRB),” (with D. Foti), Monograph Series in Earthquake Engineering, Edited by A.H. Barbat, CIMNE
Monograph IS-18, International Center for Numerical Methods in Engineering (1996).
[306] “Viscoelastic Damper Overview for Seismic and Wind Applications,” (with E.J. Nielsen, M.L. Lai and T.T.
Soong), Proceedings, 1st World Conference on Structural Control, 3:FP3-42 - FP3-51, Los Angeles, Calif.
(1994).
[307] “Viscous Heating of Fluid Dampers during Seismic and Wind Excitations: Analytical Solutions and Design
Formulae,” (with N. Makris, Y. Roussos and A.S. Whittaker), Report No. UCB/EERC-97-11, Earthquake
Engineering Research Center, University of California, Berkeley, Calif. (November 1997).
[308] “The Analysis and Design of Elastomeric Bearings for Application in Bridges,” Proceedings, U.S.-Italy
Workshop on Seismic Protective Systems for Bridges, New York, New York (May 1998).
[309] “Damping and Near-Field Effects-Their Role in Seismic Isolation,” Proceedings, 1998 Annual Meeting Los
Angeles Tall Buildings Structural Design Council, Los Angeles, CA (May 1998).
[310] “Engineering Mechanics in Earthquake-Resistant Design,” Proceedings, 12th Engineering Mechanics
Conference, La Jolla, CA (May 1998).
[311] “Seismic Isolation of Civil Buildings in the USA,” Progress in Structural Engineering Mechanics, 1(3):279-
285 (April 1998).
[312] “The Current State of Base Isolation in the United States,” Proceedings, 2nd World Conference on Structural
Control, Kyoto, Japan (June 1998).
[313] “Macroscopic Models with Complex Coefficients and Causality,” (with N. Makris and J.A. Inaudi), Journal of
Engineering Mechanics, 122(6):566-573 (1996).
[314] “The Role of Damping in Seismic Isolation,” Proceedings, Joint ASME/JSME Pressure Vessels and Piping
Conference, Seismic Shock and Vibration Isolation, San Diego, California (July 1998).
[315] “Influence of Material Stiffening on Stability of Elastomeric Bearings at Large Displacements,” (with M.
Imbimbo), Journal of Engineering Mechanics, 124(9):1045-1049 (1998).
[316] “Ongoing Studies of the Foothill Communities Law and Justice Center,” (with P.W. Clark and I.D. Aiken),
Proceedings, ASCE Structures Congress XV, 2:1133-1137, Portland, Oregon (April 1997).
[317] “Seismic Isolation as an Innovative Approach for the Protection of Engineered Structures,” Proceedings, 11th
European Conference on Earthquake Engineering, Paris, France (September 1998).
[318] “Mechanics in Earthquake Engineering,” Keynote Speaker, Proceedings, International Conference on
Theoretical, Applied, Computational, and Experimental Mechanics, Kharagpur, India (December 1998).
[319] “Role of Damping in Seismic Isolation,” Earthquake Engineering and Structural Dynamics, 28:3-20 (1999).
[320] “Experimental Studies of the Ultimate Behavior of Seismically-Isolated Structures,” (with P.W. Clark and I.D.
Aiken), UCB/EERC-97/18, Earthquake Engineering Research Center, University of California, Berkeley,
Calif. (January 1999).
[321] Design of Seismic Isolated Structures (with F. Naeim), John Wiley, New York (1999).
[322] “The Theory of Seismic Isolation and its Implementation in the United States,” Keynote address, International
Seminar on the Design of Structures, K.E.E.R.C., Seoul, Korea (April 1999).
[323] “Base Isolation in the 21st Century,” Keynote address, “Third International Conference on Seismology and
Earthquake Engineering, Tehran, Iran (May 1999).
[324] “Analysis of Fiber-Reinforced Elastomeric Isolators,” Journal of Seismic Earthquake Engineering, 2(1):19-34
(1999).
[325] “New Applications and R&D for Isolated Civil Buildings in the United States,” Proceedings, Post-SMiRT
Conf. on Seismic Isolation, Passive Energy Dissipation and Control of Vibrations of Structures, Cheju Island,
17
Korea (August 1999).
[326] “The Evolution of Seismic Isolation in the United States,” Keynote Lecture, X Congress National, La Sociedad
Mexicana de Ignenieria Sismico, Morelia, Mexico (November 1999).
[327] “The Low-Cost Light-Weight Isolators for the Seismic Protection of Housing in Developing Countries,
Keynote Lecture, Seminario 2000 Desastres Sismicos, Caracas, Venezuela (February 2000).
[328] “Torsional Displacements in Base Isolated Buildings”,(with R.S.Jangid), Earthquake Spectra. 16(2):443-
454,(2000).
[329] “Base Isolation for Near-Fault Motions”,(with R.S.Jangid), Earthquake Engineering and Structural Dynamics
30:691-707,(2000)
[330] “Stiffness Analysis of Fiber-Reinforced Elastomeric Isolators”,(with H.C.Tsai), PEER 2001/05, Pacific
Earthquake Engineering Research Center, University of California, Berkeley, (May 2001).
[331] “Analytical and Experimental Study of Fiber-Reinforced Isolators”,(with Shakzhod M. Takhirov), PEER 2001/
11, Pacific Earthquake Engineering Research Center, University of California, Berkeley, (September 2001).
[332] “Stiffness Analysis of Fiber-Reinforced Rectangular Isolators”,(with H.C.Tsai), ASCE Journal of Engineering
Mechanics, 128(4):462-470,(2002).
[333] “Progress of Application and R.&D. for Seismic Isolation for Civil Structures in the United States”,
Proceedings of the 7th. Int. Sem. on Seismic Isolation, Passive Energy Dissipation and Active Control of
Vibrations of Structures, Assisi, Italy, (October 2001).
[334] “The Seismic Protection of Large Public Buildings: The Main Requiremennts and Benefits of using Innovative
Anti-Seismic Techniques”, Proceedings of the 7th. Int. Sem. on Seismic Isolation, Passive Energy Dissipation
and Active Control of Vibrations of Structures, Assisi, Italy, (October 2001).
[335] “Seismic Isolation Systems for Developing Coutries”,(EERI Distinguished Lecture 2001),Earthquake Spectra,
18(3):1150-1157,(2002).
[336] “Bending Stiffness of Fiber-Reinforced Circular Seismic Isolators”,(with H.C.Tsai), ASCE Journal of
Engineering Mechanics, 128(4):1150-1157,(2002).
[337] “Analytical and Experimental Study of Fiber-Reinforced Strip Isolators”,(with Shakzhod M. Takhirov), PEER
2002/11, Pacific Earthquake Engineering Research Center, University of California, Berkeley, (September
2002).
[338] “Tension Buckling in Multilayer Elastomeric Bearings”, ASCE Journal of Engineering Mechanics,
129(12):1363-1368,(2003).
[339] “Seismic Isolation”, in Earthquake Engineering, From Engineering Seismology to Performance Based
Engineering, (Chapter 11), Edited by Yousef Bozorgnia and Vitelmo Bertero, CRC Press. ISBN 0-8493-
14399, (2004).
[340] “Analytical and Numerical Study of Buckling in Elastomeric Bearings with Various Shape Factors”,(with
Shakzhod M. Takhirov), Report No. EERC 2004/03, Earthquake Engineering Research Center, University of
California, Berkeley, (December 2004).
[341] “Experimental Study of Steel Reinforced Rubber Bearings with Various Shim Thicknesses”,(with Shakzhod
M. Takhirov), Proceedings of the SEM X International Congress & Exposition on Experimental and Applied
Mechanics, June 7-10, Costa Mesa, California USA, pp.12-17, (2004).
[342] “Buckling of Short Beams with Warping Effect Included”,(with H.C.Tsai), International Journal of Solids and
Structures, 42, 239-253 (2005).
[343] “Buckling Load of Seismic Isolators affected by Flexibility of Reinforcement”,(with H.C.Tsai), International
Journal of Solids and Structures, 42, 255-269 (2005).
[344] “Nonlinear Model for Lead-Rubber Bearings including Axial Load Effects”,(with Keri L. Ryan and Anil K.
Chopra) ASCE Journal of Engineering Mechanics, 131(12):1270-1278,(2005).
[345] “Fiber-Reinforced Seismic Isolators as Low-Cost Alternative to Steel-Reinforced Elastomeric Bearings”,(with
Shakzhod M. Takhirov). International Conference on Earthquake Engineering (ICEE-2006), Lahore, Pakistan,
18
September 8-9, (2006).
[346] “Analytical and Numerical Studies of Tension Buckling in Multi-Layer Elastomeric Isolators”,(with Shakzhod
M. Takhirov), Procs. of the Ninth Pan American Congress of Applied Mechanics, Edited by Jeffrey W. Eischen
and Guillermo Monsivais Galindo, Merida, Yucatan, Mexico, (2006).
[347] “Seismic Isolation for Soft Storey Buildings.”(with Seval Pinarbasi and Dimitrios Konstantinidis). Procs. of the
ASSISi 10th World Conference on Seismic Isolation, Energy Dissipation and Active Vibrations Control of
Structures. Istanbul, Turkey, May 28-31, 2007.
[348] "Low-Cost Seismic Isolators for Housing in Highly-Seismic Developing Countries."(with Dimitrios
Konstantinidis), Procs. of the ASSISi 10th World Conference on Seismic Isolation, Energy Dissipation and
Active Vibrations Control of Structures. Istanbul, Turkey, May 28-31, 2007.
[349] “Fiber-Reinforced Seismic Bearings for Low-cost Seismic Isolation Systems”,(with Shakzhod M. Takhirov),
Procs. of the Tenth World Conference on Seismic Isolation, Energy Dissipation and Active Control of
Structures, Istanbul, Turkey, May 27-30, 2007.
[350] “Tension Buckling in Multi-layer Elastomeric Isolators”, (with Shakzhod M. Takhirov), Journal of Mechanics
of Materials and Structures, Vol 2, No.8, pp.1591-1606, (2007).
[351] “Analysis of the Run-in Effect in Fiber-Reinforced Isolators under Vertical Load”, Journal of Mechanics of
Materials and Structures,Vol. 3 , No. 7, 1383-1401,(2008).
[352] “Experimental Investigations on the Seismic Response of Bridge Bearings”, (with Dimitrios Konstantinidis and
Nicos Makris), Report No. EERC 2008/02, Earthquake Engineering Research Center, University of California,
Berkeley, (June 2008).
[353] “The Effect of Friction on Unbonded Elastomeric Bearings”, (with Dimitrios Konstantinidis), Journal of
Engineering Mechanics (ASCE), Volume 135, No.9, 953-960,(2009).
[354] “Steel Shim Stresses in Multilayer Bearings under Compression and Bending”, (with Dimitrios
Konstantinidis), Journal of Mechanics of Materials and Structures,Vol. 4 , No. 6, 1109-1125,(2009).
[355] “The Stability of Non-bolted Elastomeric Isolators” (with Mario R. Marisco) in Tecnologie per L’Isolamento
ed il Controllo di Strutture e Infrastrutture, Edited by Antonella De Luca and Giorgio Serino, 2009 Ediziono
Polistampa, ISBN 978-88-596-0656-7, (2009).